{"product_id":"mad-heaters-tempest-slim","title":"MAD Heaters Tempest 2 Slim","description":"\u003ch2\u003eMAD Heaters Tempest Slim\u003c\/h2\u003e\n\u003cp\u003eThe Tempest Slim by MAD Heaters is the most recent vaporizer installment in the MAD Heaters line up and boasts a nearly identical performance to its predecessor, The Tempest 2, but in a more affordable and more convenient slim sized body. The Tempest Slim’s tip and cap remain the same as the Tempest 2 and utilize the same technology for even and consistent heating and come pre-loaded with beads. The Tempest Slim’s body, however, is quite different: longer yet slimmer. The new body features a soft grip on the sleeve which feels nice to the touch as well as a less top-heavy design for a more balanced hold. Primarily the Tempest Slim is designed to retain the phenomenal performance that Tempest 2 enjoyers are familiar with, but with a more cost effective approach to manufacturing to make this unit more affordable for those who are looking for a top-of-the-line stem vaporizer.\u003c\/p\u003e\n\u003ch3\u003eFeatures of the Tempest Slim\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eLonger yet slimmer body than the Tempest 2\u003c\/li\u003e\n\u003cli\u003eBalanced design with soft-touch grip\u003c\/li\u003e\n\u003cli\u003e3mm pre-installed Zirconia beads \u003cem\u003eon Titanium models\u003c\/em\u003e\n\u003c\/li\u003e\n\u003cli\u003e3mm pre-installed Quartz beads \u003cem\u003eon Stainless Steel models\u003c\/em\u003e\n\u003c\/li\u003e\n\u003cli\u003eSame tip and cap as Tempest 2\u003c\/li\u003e\n\u003cli\u003eAffordable design\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eItems Included with the Tempest Slim\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eThe Tempest 2 Slim Vaporizer\u003c\/li\u003e\n\u003cli\u003eHead with pre-installed 3mm Zirconia balls (Titanium models) or 3mm Quartz (Stainless Steel Models)\u003c\/li\u003e\n\u003cli\u003eLong\/slim cooling unit\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eHow to use the Tempest Slim\u003c\/h3\u003e\n\u003cp\u003eBefore use, disassemble the Tempest 2 and clean the components with isopropyl alcohol. (Note: please wipe the head assembly clean. Do not soak it as this can corrode internal components. Dry thoroughly.)\u003c\/p\u003e\n\u003cp\u003eReassemble the device and perform a burn off by heating the cap, while empty, until you hear the click. Allow it to cool and repeat 2-3 times to ensure any residues from cleaning or manufacturing have been burnt off.\u003c\/p\u003e\n\u003cp\u003eUnscrew the cap and load your material without packing too tightly so that air can flow properly through your material. Screw the cap back on gently.\u003c\/p\u003e\n\u003cp\u003eIf using a torch, use a medium single or dual flam torch and hold the tip of the flame a little less than half an inch away from the cap while slowly rotating the device. Watch the visual indicator and listen for the click that indicates that it’s ready to use.\u003c\/p\u003e\n\u003cp\u003eIf using an induction heater, place the Tempest 2 into the induction heater set your temperature around 550 degrees Fahrenheit as a baseline (adjust as needed), insert the tip, and allow the heater to run until the heating cycle finishes.\u003c\/p\u003e\n\u003cp\u003eTake a strong steady draw and use the stem’s carb hole to clear the vapor.\u003c\/p\u003e\n\u003ch3\u003eImportant information about the Tempest Slim\u003c\/h3\u003e\n\u003cp\u003eThe Tempest Slim can get hot with back-to-back use. \u003cem\u003eAllow to completely cool between uses to avoid overheating.\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eSome Wand induction heaters may have an opening too narrow to be compatible with the Tempest Slim.\u003c\/em\u003e Ensure your Wand has an opening of at least 14.0 mm. If necessary, use glass sanding paper to carefully widen it. If there is no wiggle room, do not attempt to use it, as the glass may break during heating.\u003c\/p\u003e\n\u003cp\u003e*** IMPORTANT: When cleaning head assembly, \u003cem\u003eit must be dried completely afterwards\u003c\/em\u003e before re-assembling. Soaking the head assembly and letting it air dry can corrode the components of the head assembly. These cannot be warrantied or returned if they are corroded.\u003c\/p\u003e","brand":"Mad Heaters","offers":[{"title":"Stainless Steel","offer_id":53100109070653,"sku":null,"price":139.0,"currency_code":"USD","in_stock":true},{"title":"Titanium","offer_id":53100109103421,"sku":null,"price":159.0,"currency_code":"USD","in_stock":false},{"title":"Stainless Steel - All Black","offer_id":53106541953341,"sku":null,"price":149.0,"currency_code":"USD","in_stock":true},{"title":"Titanium - All Black","offer_id":53106541986109,"sku":null,"price":169.0,"currency_code":"USD","in_stock":true},{"title":"Titanium - Lime Green","offer_id":53106542018877,"sku":null,"price":179.0,"currency_code":"USD","in_stock":true},{"title":"Titanium - Purple","offer_id":53106542051645,"sku":null,"price":179.0,"currency_code":"USD","in_stock":true},{"title":"Titanium - Aqua","offer_id":53106542084413,"sku":null,"price":179.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0017\/1828\/8436\/files\/Madheaters_Tempest_2_Slim.png?v=1790785523","url":"https:\/\/vgoodiez.com\/products\/mad-heaters-tempest-slim","provider":"VGoodiEZ","version":"1.0","type":"link"}